|
Tis item is 100% compatible with
Atmel's AT JTAGICE mkII, It supports
AVR32 series of MCUs and can upgrade
with avrstudio's upgrade tool.
a
powerful development tool for
On-chip Debugging of all AVR 8-bit
RISC MCUs and AVR32 32-bit DSP/MCUs
with IEEE 1149.1 compliant JTAG
interface.
Combined with AVR Studio the JTAGICE
mkII can do On-Chip Debugging on all
AVR 8-bit RISC microcontrollers with
JTAG Interface or debugWIRE
Interface. Click here for a list of
supported devices.
JTAG
The JTAG interface is a 4
wire Test Access Port (TAP)
controller that is compliant with
the IEEE 1149.1 standard. The IEEE
standard was developed to enable a
standard way to efficiently test
circuit board connectivity (Boundary
Scan). Atmel AVR devices have
extended this functionality to
include full Programming and On-Chip
Debugging support.
The JTAGICE mkII uses the
standard JTAG interface to enable
the user to do real time emulation
of the microcontroller while it is
running in the target system.
The AVR On-Chip Debug (AVROCD)
protocol gives the user complete
control of the internal resources of
the AVR microcontroller. Thus
JTAGICE mkII gives accurate
emulation at a fraction of the cost
of traditional emulators.
debugWIRE
The debugWIRE interface
adds a new way of doing On Chip
Debug. The debugWIRE On-chip debug
system uses a one-wire,
bi-directional interface to control
the program flow, execute AVR
instructions in the CPU and to
program the different non-volatile
memories.
When the debugWIRE Enable (DWEN)
Fuse is programmed and Lock bits are
un-programmed, the debugWIRE system
within the target device is
activated. The RESET port pin is
configured as a wire-AND
(open-drain) bi-directional I/O pin
with pull-up enabled and becomes the
communication gateway between target
and emulator.
Note that debugWIRE is a
debugging interface only and not a
programming interface.
ISP
The JTAGICE mkII also
supports full programming through
the ISP interface. All JTAG and
debugWIRE parts are supported. See
Programming with JTAGICE mkII for
more information.
It
works on either USB port or RS232
seriel port.
JTAGICE mkII features
- AVR Studio Compatible (AVR
Studio 4.09 or later)
- Supports all AVR Devices
with JTAG Interface
- Supports all AVR Devices
with debugWIRE Interface
- Supports ISP programming of
all JTAG and debugWIRE parts
- Exact Electrical
Characteristics
- Emulates Digital and Analog
On-Chip Functions
- Software Breakpoints
- Program Memory Breakpoints
- Supports Assembler and HLL
Source Level Debugging
- Programming Interface to
flash, eeprom, fuses and
lockbits (JTAG only)
- USB 1.1 and RS232 Interface
to PC for Programming and
Control
- Regulated Power Supply for
9-12V DC Power
- Can be powered from the USB
alone
- Same hardware for both
interfaces (JTAG and debugWIRE)
- Auto firmware upgrade if
there is new firmware available
in future new AVR Studio
software.
8-bit AVR:
The JTAGICE mkII also support
devices with debugWIRE Interface.
debugWIRE enables on-chip debug of
AVR microcontrollers in small pin
count packages, using only a single
wire for the debug interface.
The
AVR
Studio
online-help contains the most
current information and a complete
list of supported devices.
Read more about
AVR
8-bit RISC
microcontrollers.
32-bit AVR32:
The JTAGICE mkII is supported by the
AVR32
Studio.
Read more about
AVR32
32-bit MCU/DSP.
AVR XMEGA
Read
AVR XMEGA from Atmel
More information,you can visit
this url from atmel's JTAGICE mkII.
http://www.atmel.com/dyn/products/tools_card.asp?family_id=607&family_name=AVR%AE+8%2DBit+RISC+&tool_id=3353
Support Device:
AVR 8-BIT MCU
JATG:
mega Series:
ATmega16
ATmega162 ATmega32 ATmega64
ATmega128 ATmega169 ATmega169P
ATmega329 ATmega329P ATmega3290
ATmega3290P ATmega649 ATmega6490
ATmeg164P ATmega324P ATmega644P
ATmega165 ATmega165P ATmega325
ATmega325P ATmega3250 ATmega3250P
ATmega645 ATmega6450 ATmega640
ATmega1280 ATmega1281 ATmega2560
ATmega2561
Xmega
Series:
ATxmega128A1 ATxmega64A1
Other Series:
AT90CAN32 AT90CAN64
AT90CAN128 AT90USB162 AT90USB646
AT90USB647 AT90USB1286 AT90USB1287
DebugWIRE:
mega Series:
ATmega48
ATmega48P ATmega88 ATmega88P
ATmega168 ATmega168P
tiny
Series:
ATtiny13 ATtiny2313
ATtiny24 ATtiny44 ATtiny84 ATtiny25
ATtiny45 ATtiny85 ATtiny261
ATtiny461 ATtiny861
Other
Series:
AT90PWM3 AT90PWM3B
AT90PWM2 AT90PWM2B AT90USB162
AVR 32-BIT MCU
JATG:
AT32AP7000 AT32AP7001 AT32AP7002
AT32UC3A0128 AT32UC3A0256
AT32UC3A0512 AT32UC3A1128
AT32UC3A1256 AT32UC3A1512
AT32UC3B0128 AT32UC3B0256
AT32UC3B064 AT32UC3B1128
AT32UC3B1256 AT32UC3B164
Support "L" or "V" Serirs Device,
For example:
ATmega16L、ATmega48V
Support Target Board VDD 2.1-5.5V
The onboard firmware is upgradeable
via AVRStudio IDE to support newly
introduced devices.
Package includes the following item:
1: AVR
JTAGICE MKII *
1
2. USB Cable * 1
3. DB9/RS232 Cable *1
4. 10PIN JTAG Cable Backup *1
5. 10PIN JTAG Cable with OUT Reset
Line *1
6. JTAG TO ISP 10PIN Cable *1
7. JTAG TO ISP 6PIN Cable *1
8. 10-PIN TO 10 x 1PIN cable *1
9: CD ROM(AVR Studio software; user
manuals....) * 1 |